Viz Mosart Administrator Guide

Version 5.2 | Published May 22, 2023 ©

Control Commands in Templates

A Mosart control command can be triggered from a template, executed when the template is taken (Command On Take), at continue points (Continue Points) or when the template is taken out (Command On Take Out).

Note:

  • A Mosart template can trigger multiple control commands.

  • A (not-templated) control command can trigger a Mosart template, often used for a DirectTake template.

Working with Control Commands

This is done through AV Automation > Devices > Template Editor > Template > Properties > Control Commands tab.
images/download/attachments/120746112/cComm.png

The figure above shows a single (video) control command to be executed when the template is taken. Multiple control commands can be assigned here.

It is also possible to assign control commands to be executed at continue points and when the template is taken out.

The latter has limitation since the Parameter setting is not available. In this context it may be useful to trigger a direct take at this place.

Adding a Control Command

To Add a Control Command

images/download/attachments/120746112/comSet.png

Commands on Cue

You can recall control commands in Preview, when the template is cued. This enables triggering of events when a story item is taken to Preview.
images/download/attachments/120746112/cOT.png

As illustrated above, you can give the command a Value and a Parameter in the same way as for Command On Take, Command on Take Out.
Also, in a similar way to Continue Points you can set an offset for when the command is to be executed.

Note: For Cue commands, all offsets are relative to the start of cueing. This differs from Continue Points, where each offset is relative to the previous continue point.
In the illustration above, the User Message (Ready) will be sent 100 frames after cueing.

By defining a Newsroom tag as a parameter for an On Cue command, the user can set the parameter from the NRCS.

  • In the Parameter column right-click and select either Add/Remove/Change a newsroom tag .

Command On Take

When selected, the commands inserted in Control commands Take are executed when the template is taken to Program or On Air.

By defining a Newsroom tag as a parameter for an On Take command, the user can set the parameter from the NRCS.

  • In the Parameter column, right-click and select either Add/Remove/Change a newsroom tag .

Continue Points

When selected, the commands inserted in Continue Points will be taken when pressing TAKE NEXT (default: F12). Viz Mosart executes this continue point from within the primary template in which it is inserted. Each line represents a new Continue Point.
images/download/attachments/120746112/autoT.png

  • Cue Next Item Index: Enter the line number (for example, 0, 1, 2, 3) of the continue point that executes a cue for the next/following Primary object. If empty, Viz Mosart cues when entering the last continue point in the list.

  • Autotake: Insert the autotake time, in frames. The command is then automatically taken after that time.

    Note: For Continue Points, all offsets are relative to the last Continue Point. This differs from Commands on Cue, where each offset is relative to the start of cueing.
    In the illustration above, the Device Property is fetched 20 frames after being taken on-air, Player Status is fetched at 50 frames later and from the NRCS, the Stop Status at 110 frames after the previous (Get Player Status) Continue Point was processed.

By defining a Newsroom tag as a parameter for a Continue Point, the user can set the parameter from the NRCS.

  • In the Autotake column right-click and select either Add/Remove/Change a newsroom tag.

Command on Take Out

The commands inserted here are executed when the template is taken from the program, taken Off Air, or at the end of the template. Only a single command can be used in Command On Take Out, and it does accept any parameters.

Command Values and Parameters

Note: Parameters marked with (*) do not work for templates.

Note: It is not possible to enter a Parameter in the Control command Take Out section.

COMMAND

Value

Parameter

Description

ACCESSORIES

TAKE_NEXT

(*)


AUDIO

FADE_MANUAL


Toggle fade manual.


FADE_OUT_KEEPS

Fader rate

Faders that are set as "keep level" in the template On Air are faded out. Will also work when new templates have been taken in between the 'keep' action and the FADE_OUT_KEEPS.


FADE_DOWN SECONDARY_AUDIO

Fader rate

Viz Mosart fades down relevant audio sources not connected to the video currently On Air.


FADE_UP SECONDARY_AUDIO

Fader rate

Viz Mosart fades up relevant audio sources not connected to the video currently On Air, when cutting between sources.


SET_LEVEL_2_ONAIR

-

The second level for faders in the template which are On Air are set.


SET_LEVEL_2_PREVIEW

-

The second level for faders in the template are set on the template which is in preview, and be performed on next transition.


FREEZE_AUDIO

-

All sound faders are frozen, and do not respond to commands from templates. This command is a toggle function, and is thus NOT suited for use from a template.

AUTOTAKE

N/A

(*)


AUTOTRANS

PP, ME1, ME2, ME3, ME4

MixEffect (MIX OR WIPE) + Transitionrate

For example: MIX 33, WIPE 10.

Note: The Effect cannot be used.


AUX, Default

(*)


CROSSOVERCOMMAND

N/A

(*)


DEVICE_PROPERTY

CAMERA CONTROL

See next column.

Note: This is for camera robotics.

When the DEVICE_PROPERTY control command is used with the value 'CAMERA CONTROL', only setting speed (Camerobot) and presenter (Camerobot/FxMotion) are controllable from a template.

Details for Camerobot Presenter:

ANCHOR=pos1:presenter1[,pos2:presenter2]…

The position and presenter is given as a pair divided by ‘:’.

Multiple position-presenter pairs are possible, separated by ‘,’. images/download/attachments/120746112/Template_properties_closer1.png

Note: The position is a string and does not have to be a number.

Details for Camerobot Time:

If Time =1 (>0), Viz Mosart sends MATRIX_MOVE_MPOS command to Camerobot,
while if Time = 0 Viz Mosart sends MATRIX_CUT_MPOS command Camerobot.


AUDIO

demands <fields> structure as parameter with
parameter1=AUDIO,
parmeter2=key,
parameter3=value
OR
connectionstring style

Note: This is for an audio mixer.

DEVICE_STANDBY

AUDIO_MIXER, GPI, LIGHTS, LOUDNESS, ROUTER, SOUND_PLAYER, SUBTITLING, VIDEO_SERVER, VIDEO_SWITCHER, VIDEO_WALL, VIRTUAL_SET, WEATHER

ON

OFF

TOGGLE

ON: The device chosen (in Value) is put in Standby.

OFF: The device chosen (in Value) is taken out of Standby.

TOGGLE: The Standby status (ON/OFF) of the device chosen (in Value) is toggled.

(If there are several devices of the chosen kind (e.g. video servers), all of them are affected.)

DEVICE_STANDBY

GRAPHICS (full-screen)

As above (ON/OFF/TOGGLE)

OR

engineno:[ON|OFF|TOGGLE]
(Example: 2:TOGGLE)

ON/OFF/TOGGLE: As above, applied to all graphics engines.


If an engine number is given, only the designated engine is affected.

DEVICE_STANDBY

ROBOTIC_CAMERA

As above (ON/OFF/TOGGLE)

OR

controller:[ON|OFF|TOGGLE]
(Example: 1:ON)

OR

controller:camera:[ON|OFF|TOGGLE]
(Example: 1:2:ON)

ON/OFF/TOGGLE: As above, applied to all cameras on all controllers.


If a controller (but no camera) is given, only the cameras on the designated controller are affected.


If both a controller and a camera is given, only the designated camera is affected.

DEVICE_STANDBY

OVERLAY_GRAPHICS

As above (ON/OFF/TOGGLE)

OR

Engine No:[ON|OFF|TOGGLE]

For example:
2:TOGGLE: Toggles Engine 2 Standby status)

ON/OFF/TOGGLE: Applied to all overlay graphics (all controllers and corresponding engines).

If an engine number is given, only the designated engine is affected.

Note: Only engine number is supported.
Engine numbers are shown in the list of active engines in Overlay Graphics Interface and followed by '/' and destination name of the engine.
(Engine Handler, Destinations, Controller have no effect).

DIRECTTAKE

The Recall Nr (see Template Properties) of the direct take template to execute

-

Executes the direct take template given by Value.

DVE

FORWARD

REVERSE

Recall forward/reverse EMEM

n/a

ENABLE_GRAPHICS_
MIRRORING

n/a

(*)


FULLSCREEN_GRAPHICS

CONTINUE_FULLSCREEN

AUTO

Continue Command Only: The AUTO parameter will replace the continue command with the number of continue points in the graphics item.
The number of continue points is taken from the graphics_continuecount field.

Examples:
AUTO+1: The number of continue counts from the graphics + 1
AUTO-2: The number of continue counts from the graphics - 2

FULLSCREEN_GRAPHICS

CONTINUE_FULLSCREEN

Engine no

The target output fullscreen engine number to execute the action on. (e.g. 1,2,3 )


MACRO

Engine no : macro

The target output fullscreen engine number to execute the action on. (e.g. 1,2,3 ) and Macro name.

The engine number must be same as the number defined in AV Automation

GRAPHICSPROFILE

N/A

-


HOLD_AUDIO_
TRANSITION

N/A

-


HOLD_VIDEO_
TRANSITION

N/A

-


LIGHT

N/A

(*)


MARKER

N/A

(*)


NCS

START_STATUS,

STOP_STATUS

RUNDOWN

STORY

ITEM

Specific for Open Media

NEXT_CUE_DELAY

EXTEND

A number of frames

If there is a pending cue (when this control command is executed), this cue is postponed by the number of frames given.

Otherwise (no pending cue), the next cue operation will be additionally delayed by the number of frames given. (I.e., the value will be added to the sum of the settings

OVERLAY_GRAPHICS

CLEAR

Destination or Render (Engine no.)

Destination or Render (Engine no.) to clear the graphics from.

Numerical value: Render (Engine no.)

Non-numerical value: Destination.


CONTINUE

Engine no



TAKE_MANUAL_OUT

Destination or Empty

Destination to take out the graphics from.

Non-numerical value: Destination

Empty or Numerical value: Takes out all the graphics


MACRO

Engine no : macro

For example: 4:macrohere


PRETAKE_NEXT_OVERLAY

Render (engine no)



TAKE_NEXT_OVERLAY,

TAKE_NAMED_OVERLAY

(*)


OVERLAY_TO_MANUAL

Parameter 1: ONAIR (default), PREVIEW.

Parameter 2: Comma-separated list of handler names

Parameter 3: AUTOMATIC (default) / MANUAL

Parameter 2 and Parameter 3 must be separated by a semicolon. (E.g. WALL,DSK;MANUAL.)

For more details, see Viz Mosart User Interface > Keyboard Shortcuts > Control Command Keys > OVERLAY_TO_MANUAL in the Viz Mosart User Guide).

Note : If there is no semicolon after Parameter 2; nothing to the right of the semicolon; or Parameter 3 has any value other than 'MANUAL', then Parameter 3 gets the default value ‘AUTOMATIC’.

PLAY_STORY

N/A

(*)


RECORD

PREPARE,

START,

STOP

Split parameters using,

- first: clipname,

- second: recorder (optional),

- third: port name (default Rec),

- fourth: group name (default Rec)

For example: clip33,recorder1,Rec,Rec

RELEASE_BACKGROUND

N/A

(*)


RUNDOWN_NCS_
RESYNC

N/A

(*)


SEQUENCE

LOOP

-

Sets a running sequence to start looping


STOP_LOOP

-

Stops running a looped sequence in loop


STOP

-

Stops a running sequence


START

-

Restarts a previously stopped sequence

SET_AUX_CROSSPOINT

N/A

(*)


SET_CROSSPOINT

PP, ME1, ME2, ME3, ME4

AUX

Default

bus (A,B,C,D) : xpoint

If layers are supported by the driver (e.g. vizrt-ips) it is possible to also specify the layer (A,B,C,D) in addition to the crosspoint.

Two arguments are supported separated by semicolon. First parameter is crosspoint, the second is layer.

If no semicolon is used the value is interpreted as crosspoint only and bus A is used.


Example: B:CAM2

SET_CURRENT_ME

PP, ME1, ME2, ME3, ME4

AUX

Default

(*)






SET_VIDEOSERVER_
SALVO

Select a configured video server from the list

-

These same settings are available as keyboard shortcuts, as presented in the Viz Mosart User Guide, under section Viz Mosart User Interface.

STUDIOSETTUP

#

-


SWITCH_GRAPHICS_
MIRRORING

TOGGLE,

ACTIVATE,

DE-ACTIVATE

-

For standard and Story Recorder (SR) shows.

SWITCH_GENLOCK_MODE

TOGGLE,

ACTIVATE,

DE-ACTIVATE


Story Recorder (SR) specific:
As long as some standard show elements are not supported with SR, use this command to control the use of Genlock mode.

SR can only run in Genlock mode.

SWITCH_REHEARSAL_MODE

TOGGLE,

ACTIVATE,

DE-ACTIVATE


Story Recorder (SR) specific:
SR can only run with Rehearsal mode deactivated, use this command to ensure Rehearsal mode is not accidentally active.

SWITCH_VIDEOSERVER_
MIRRORING

N/A

-

For standard and Story Recorder (SR) shows.

This command has no parameters, it simply acts as a toggle.

TAKE_CONTINUE_POINT

N/A

(*)


TAKE_SERVER_TO_
PROGRAM

N/A

transRate (integer) - parameter.

(*)

Takes a video server port to program on a selected ME. For example: a video clip is running on a video wall.
The shortcut can then be used to take the last used/active video server to program.

TRANSITION_TYPE

CUT,

MIX

Rate



EFFECT

Effect no



TOGGLE

(*)


UNKNOWN

N/A


Default fallback. Does nothing.

VIDEO_PORT

N/A

Must be a comma separated list in the format:

command,port,parameter

For example: PLAY_PAUSE,A,PLAY.

For more details, see Viz Mosart User Interface > Keyboard Shortcuts > Video Port Control Commands > OVERLAY_TO_MANUAL in the Viz Mosart User Guide).

VIDEO_SERVER_GOTO

N/A

(*)


VIDEOWALLMODE

N/A

(*)


WEATHER

N/A

(*)


Parameters with Placeholders

Control command parameters can include placeholders which are then populated with values found among the fields of a currently On Air, Viz Mosart item. A placeholder is defined as a string of characters, within curly brackets {placeholder}.
For example, a placeholder can be useful for transmitting values from the NRCS, for use as control commands that will be executed when the template is taken On Air.

Example: Providing the clip name to be recorded from NRCS.

In the NRCS, a column can be created for giving the name of the clip to be recorded with Viz Mosart. Then, in Viz Mosart Newsroom settings, map the column in Story External Metadata as follows:

Story External Metadata
<mostag mostagname="NCScolumn" mosart_action="item_variable" action_value="NCS_filename" format_type="String" />

In Manus file, the Mosart item will have the following fields (the value Clip1 is given from the NRCS):

Mosart Item
<fields>
<field name="NCS_filename" value="Clip1" />
</fields>

Then, in Template Editor, the control command for the respective template is configured as follows:

Control Command
RECORD PREPARE {NCS_filename}_Test,Recorder,RecPort

When the template is executed, a clip with name Clip1_Test is prepared for recording.